Jeep Cherokee (KL): Enabling And Disabling ParkSense. Service The ParkSense Park Assist System. ParkSense System Usage Precautions

Jeep Cherokee (KL) 2014 - 2023 Owners Manual > Understanding the features of your vehicle > Parksense front and rear park assist > Enabling And Disabling ParkSense. Service The ParkSense Park Assist System. ParkSense System Usage Precautions

Enabling And Disabling ParkSense

ParkSense can be enabled and disabled with the ParkSense switch, located on the switch panel below the Uconnect display.

ParkSense Switch
ParkSense Switch

When the ParkSense switch is pushed to disable the system, the instrument cluster will display the "PARKSENSE OFF" message for approximately five seconds.

Refer to "Electronic Vehicle Information Center (EVIC)" in "Understanding Your Instrument Panel" or "Driver Information Display (DID)" for further information.

When the shift lever is moved to REVERSE and the system is disabled, the EVIC/DID will display the "PARKSENSE OFF" message for as long as the vehicle is in REVERSE.

The ParkSense switch LED will be ON when ParkSense is disabled or requires service. The ParkSense switch LED will be OFF when the system is enabled. If the ParkSense switch is pushed, and requires service, the ParkSense switch LED will blink momentarily, and then the LED will be ON.

Service The ParkSense Park Assist System

During vehicle start up, when the ParkSense System has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the PARKSENSE UNAVAILABLE WIPE REAR SENSORS , PARKSENSE UNAVAILABLE WIPE FRONT SENSORS , or the PARKSENSE UNAVAILABLE SERVICE REQUIRED message for five seconds.

When the shift lever/gear selector is moved to Reverse and the system has detected a faulted condition, the Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID) will display a PARKSENSE UNAVAILABLE WIPE REAR SENSORS , PARKSENSE UNAVAILABLE WIPE FRONT SENSORS or PARKSENSE UNAVAILABLE SERVICE REQUIRED pop up message for five seconds. After five seconds, a car graphic will be displayed with UNAVAILABLE at either the front or rear sensor location depending on where the fault is detected. The system will continue to provide arc alerts for the side that is functioning properly. These arc alerts will interrupt the PARKSENSE UNAVAILABLE WIPE REAR SENSORS , PARKSENSE UNAVAILABLE WIPE FRONT SENSORS , or PARKSENSE UNAVAILABLE SERVICE REQUIRED messages if an object is detected within the five second pop-up duration. The car graphic will remain displayed for as long as the vehicle is in REVERSE. Refer to "Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID)" for further information.

If PARKSENSE UNAVAILABLE WIPE REAR SENSORS or PARKSENSE UNAVAILABLE WIPE FRONT SENSORS appears in the Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID) make sure the outer surface and the underside of the rear fascia/bumper and/or front fascia/bumper is clean and clear of snow, ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to appear see an authorized dealer.

If the PARKSENSE UNAVAILABLE SERVICE REQUIRED message appears in the EVIC/DID, see an authorized dealer.

Cleaning The ParkSense System

Clean the ParkSense sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors.

ParkSense System Usage Precautions

NOTE:

  • Ensure that the front and rear bumper are free of snow, ice, mud, dirt and debris to keep the ParkSense system operating properly.
  • Construction equipment, large trucks, and other vibrations could affect the performance of ParkSense.
  • When you turn ParkSense off, the instrument cluster will display "PARKSENSE OFF." Furthermore, once you turn ParkSense off, it remains off until you turn it on again, even if you cycle the ignition key.
  • When you move the shift lever to the REVERSE position and ParkSense is turned off, the instrument cluster will display "PARKSENSE OFF" for as long as the vehicle is in REVERSE.
  • ParkSense, when on, will reduce the volume of the radio when it is sounding a tone.
  • Clean the ParkSense sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris.

    Failure to do so can result in the system not working properly. The ParkSense system might not detect an obstacle behind or in front of the fascia/bumper, or it could provide a false indication that an obstacle is behind or in front of the fascia/bumper.

  • Use the ParkSense switch to turn the ParkSense system off if objects such as bicycle carriers, trailer hitches, etc.

    are placed within 12 in (30 cm) from the rear fascia/ bumper. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the "PARKSENSE UNAVAILABLE SERVICE REQUIRED" message to be displayed in the instrument cluster.

  • ParkSense should be disabled when the liftgate is in the open position. An opened liftgate could provide a false indication that an obstacle is behind the vehicle.
  • There may be a delay in the object detection rate if the object is moving. This will cause the automatic braking application to be delayed.

CAUTION!

  • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.

    Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity.

  • The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense.

WARNING!

  • Drivers must be careful when backing up even when using ParkSense. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up.

    You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death

  • Before using ParkSense, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the loudspeaker sounds the continuous tone. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

    Previous pageParkSense Sensors. ParkSense Warning Display. ParkSense Display

    ParkSense Sensors The four ParkSense sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors' field of view. The sensors can detect obstacles fro ...

    Next pageParksense active park assist system

    The ParkSense Active Park Assist system is intended to assist the driver during parallel and perpendicular parking maneuvers by identifying a proper parking space, providing audible/visual instruct ...

    Other materials:

    Child Restraints
    Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 ...