Toyota
Jeep Cherokee
 Service Manual
Power mirror systems » Removal and installation
Power mirror

(1) Disconnect and isolate the battery negative cable.

(2) If the vehicle is so equipped, remove the manual window regulator crank handle with a removal tool (Fig. 7).

(3) Remove the screws that secure the front door trim panel to the inner door panel (Fig. 8) or (Fig. 9).

(4) Using a trim stick or another suitable wide flat-bladed tool, gently pry the front door trim panel away from the door around the perimeter to release the trim panel retainers.

Fig. 6 Door Module Remove/Install
Fig. 6 Door Module Remove/Install

1 - INSIDE DOOR LATCH AND LOCK REMOTE CONTROLS
2 - CONNECTOR 1 RECEPTACLE
3 - DOOR MODULE
4 - CONNECTOR 2 RECEPTACLE
5 - SCREWS
6 - DOOR TRIM PANEL

Fig. 7 Window Regulator Crank Handle Remove - Typical
Fig. 7 Window Regulator Crank Handle Remove - Typical

1 - DOOR HANDLE REMOVAL TOOL
2 - WINDOW CRANK

NOTE: To aid in the removal of the trim panel, start at the bottom of the panel.

(5) Lift the front door trim panel upwards and away from the inner door panel far enough to disengage the top of the panel from the inner belt weatherstrip.

(6) Pull the front door trim panel away from the inner door far enough to access the inside door latch release and lock linkage rods near the back of the inside door remote controls.

(7) Unsnap the plastic retainer clips from the inside door remote control ends of the latch release and lock linkage rods, and remove the rod ends from the inside door remote controls.

Fig. 8 Front Door Trim Panel Remove/Install - Manual Window
Fig. 8 Front Door Trim Panel Remove/Install - Manual Window

1 - U-NUT
2 - DOOR
3 - TRIM PANEL
4 - WINDOW CRANK
5 - SPACER
6 - PUSH-IN FASTENER

Fig. 9 Front Door Trim Panel Remove/Install - Power Window
Fig. 9 Front Door Trim Panel Remove/Install - Power Window

1 - U-NUT
2 - DOOR
3 - TRIM PANEL
4 - PUSH-IN FASTENER

(8) Unplug the wire harness connectors from the door power switch module or, on the driver side only, the stand-alone power mirror switch.

(9) Set the front door trim panel aside.

(10) Remove the one screw that secures the front door flag trim to the inner door panel (Fig. 10).

(11) Using a trim stick or another suitable wide flat-bladed tool, gently pry the door flag trim away from the inner door to release the trim panel retainer

Fig. 10 Front Door Flag Trim Panel Remove/Install
Fig. 10 Front Door Flag Trim Panel Remove/Install

1 - FRONT DOOR
2 - DOOR FLAG TRIM PANEL
3 - RETAINER
4 - SCREW
5 - UPPER SPEAKER WIRE HARNESS

(12) Unplug the power mirror wire harness connector.

(13) Remove the three screws that secure the power mirror to the inner door panel (Fig. 11).

(14) Unseat the power mirror wire harness grommet by pushing it out through the hole in the door flag from the inside.

Fig. 11 Power Mirror Remove/Install
Fig. 11 Power Mirror Remove/Install

1 - SIDE VIEW MIRROR
2 - WIRE HARNESS
3 - SEAL
4 - GROMMET
5 - DOOR

(15) Pull the mirror and seal from the outside of the door while feeding the wire harness, grommet, and connector out through the hole from the inside of the door.

(16) Reverse the removal procedures to install.

Tighten the mirror mounting screws to 4.3 N·m (38 in. lbs.). Tighten the door trim mounting screws to 2.2 N·m (20 in. lbs.).

    More about «Removal and installation»:

    Power mirror switch

    Door module

    Power mirror

    Jeep Cherokee Service Manual / Power mirror systems / Removal and installation / Power mirror

    Jeep Cherokee Service Manual

    Categories


    © 2017-2024 Copyright www.jcherokee.com